These days, clip on flip up sunglasses are the in thing because not only are they very stylish, but they are also very handy to use as compared to a real pair of sunglasses. The great thing about this type of thing is that one does not necessarily need to buy one because it is so easy to make one right at home. So if one would want to try making one, then here are some instructions how.
The first step would be to get hold of an old pair of sunglasses and use a small screwdriver to take the arms of the glasses out. When one does this, then all that will be left would be a pair of lenses of the sunglasses. Take note that the pair of glasses right now is very delicate and may break if not handled well.
The next step is to grab hold of a paper clip that is quite hard so that the clip will be steady. After this, one should now get some pliers and make it very straight. Always do this very slowly because it is quite possible that the wire will break if handled too fast.
When the wire has been straightened, then one should get a pair of tough scissors and try to cut the wire into two. Then the next thing to do would be to get a wire and try to put it into the hole where the arms of the glasses was taken out. He must also do this for the other hole.
When all of the wires have been slotted into the holes, then the following step to do would be to attach the wires to the holes. In order to do this, one has to use the pliers to bend the wire so that it will be attached to the hole. Make sure to tie it in very tight otherwise the wire will just fall out later on when it is attached to the eyeglasses.
From there, take the two ends and place them in the center top part of the glasses. Always remember to embed the wires to the frame to make sure that the wire will be invisible to the eyes of the public. Once this is done, tie the two ends together in order to make a small clip in the middle.
The last thing to do here would be to make a small curve in the middle part so that it can be attached to the glasses. If there is already a small bend, then one should try clipping it on the eyeglasses to check if it looks good. If it looks fine, then one may now go out and start wearing it.
So as one can see, it is actually very easy to make a pair of clip on flip up sunglasses. The great thing about this device is that it is very practical because it is easier to use than a normal pair of sunglasses. It is also much cheaper to make one at home because the ones outside are very expensive.
The first step would be to get hold of an old pair of sunglasses and use a small screwdriver to take the arms of the glasses out. When one does this, then all that will be left would be a pair of lenses of the sunglasses. Take note that the pair of glasses right now is very delicate and may break if not handled well.
The next step is to grab hold of a paper clip that is quite hard so that the clip will be steady. After this, one should now get some pliers and make it very straight. Always do this very slowly because it is quite possible that the wire will break if handled too fast.
When the wire has been straightened, then one should get a pair of tough scissors and try to cut the wire into two. Then the next thing to do would be to get a wire and try to put it into the hole where the arms of the glasses was taken out. He must also do this for the other hole.
When all of the wires have been slotted into the holes, then the following step to do would be to attach the wires to the holes. In order to do this, one has to use the pliers to bend the wire so that it will be attached to the hole. Make sure to tie it in very tight otherwise the wire will just fall out later on when it is attached to the eyeglasses.
From there, take the two ends and place them in the center top part of the glasses. Always remember to embed the wires to the frame to make sure that the wire will be invisible to the eyes of the public. Once this is done, tie the two ends together in order to make a small clip in the middle.
The last thing to do here would be to make a small curve in the middle part so that it can be attached to the glasses. If there is already a small bend, then one should try clipping it on the eyeglasses to check if it looks good. If it looks fine, then one may now go out and start wearing it.
So as one can see, it is actually very easy to make a pair of clip on flip up sunglasses. The great thing about this device is that it is very practical because it is easier to use than a normal pair of sunglasses. It is also much cheaper to make one at home because the ones outside are very expensive.
About the Author:
Check out www.brimzsports.com for a review of the benefits of purchasing clip on flip up sunglasses online, today. You can also view our selection of sunglasses at http://www.brimzsports.com now.
0 comments:
Post a Comment